Kia EV2: Light bulbs / Headlamp aiming (for Europe). Aiming point

Kia EV2 (QV1, 2026-2026) Owner's Manual / Maintenance / Light bulbs / Headlamp aiming (for Europe). Aiming point

NOTE

Inflate the tyres to the specified pressure and remove any loads from the vehicle except the driver, spare tyre, and tools.

The vehicle should be placed on a perfectly flat floor surface to ensure accurate calibration.

Draw vertical lines (Vertical lines passing through respective head lamp centers) and a horizontal line (Horizontal line passing through centre of head lamps) on the aiming screen.

With the head lamp and battery in normal operating condition, aim the head lamps so the brightest portion falls precisely on the intersection of horizontal and vertical lines.

To aim the low beam left or right, turn the adjustment screwdriver (1) clockwise or counterclockwise. To aim the low beam up or down, turn the adjustment screwdriver (2) clockwise or counterclockwise.

Aiming point

Screen


Vehicle condition		Head lamp (LED type)
		Ground Height		Distance between lamps
		H1 (LOW)	H2 (HIGH)	W1 (LOW)
Head lamp	Without driver [mm (inches)]	836 (32.9)	704 (27.7)	1,467 (57.8)
Head lamp	With driver [mm (inches)]	830 (32.7)	698 (27.5)	1,467 (57.8)

Head lamp low beam (LHD Vehicle)

Engineering projection screen schematic for left-hand drive Kia EV2 low beam cut-off line calibration — Figure 1. Based on 10 m screen

Vehicle axis
Vehicle line of the left head lamp bulb centre
Vehicle line of the right head lamp bulb centre
Horizontal line of the head lamp bulb centre
Cut-off line
Ground

Turn the low beam on without driver aboard.
The cut-off line should be projected in the exact position shown in the reference picture.
When aiming the low beam, vertical aiming should always be adjusted after completing the horizontal adjustment.
Disengage the parking brake and shift to N (Neutral). In addition, if a headlamp levelling device is equipped, adjust the headlamp levelling device switch to 0.

Head lamp low beam (RHD Vehicle)

Engineering projection screen schematic for right-hand drive Kia EV2 low beam cut-off line calibration — Figure 2. Based on 10 m screen

Vehicle axis
Vehicle line of the left head lamp bulb centre
Vehicle line of the right head lamp bulb centre
Horizontal line of the head lamp bulb centre
Cut-off line
Ground

Turn the low beam on without driver aboard.
The cut-off line should be projected in the exact position shown in the reference picture.
When aiming the low beam, vertical aiming should always be adjusted after completing the horizontal adjustment.
Disengage the parking brake and shift to N (Neutral). In addition, if a headlamp levelling device is equipped, adjust the headlamp levelling device switch to 0.

Replacing lights (Bulb type)

Replacing the rear turn signal lamp To replace the rear turn signal lamp (bulb type), follow these steps: Make sure the vehicle is in the OFF position and disconnect the negative 12V battery terminal...

Appearance care

Use the comprehensive information and technical guidelines outlined in the following sections to keep both the exterior paintwork and interior cabin trim of your Kia EV2 in immaculate condition...

Other information:

Chevrolet Silverado 2019-2026 Owners Manual: Electrical System Overload

The vehicle has fuses to protect against an electrical system overload. Fuses also protect power devices in the vehicle. Replace a bad fuse with a new one of the identical size and rating. If there is a problem on the road and a fuse needs to be replaced, there are some spare fuses and a fuse puller in the left instrument panel fuse block...

Kia EV2 (QV1, 2026-2026) Owner's Manual: Scheduled ventilation control: (if equipped)

The advanced scheduled ventilation control function helps maintain exceptionally fresh, breathable air inside the passenger compartment of your Kia EV2 by automatically detecting and regulating cabin temperature and humidity levels even when the main climate control system has been turned off...